Return to Hobie.com
Hobie Forums
It is currently Thu Mar 28, 2024 3:48 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 11 posts ] 
Author Message
PostPosted: Sun Nov 01, 2020 7:56 am 
Offline
Site Rank - Admiral

Joined: Fri Jul 13, 2018 9:01 am
Posts: 152
Location: Near Austin, TX
Tried finding this here and on the interwebs but haven't. I'm kind of baffled that Hobie didn't make these MD chain/cable connections stronger. As they are (V2's/GTs) they are merely crimped (chain side female socket with cable end inserted). I've used silver solder, MAPP gas torch, and flux to solder SS (specifically thermocouples inside thin-walled SS tubing). I'm considering having a go at a repair, only challenges I see are two: 1. I need to get the braided SS cable inserted back into the female feral (done, as I used a Dremel diamond bit just a little smaller in diameter to bore out the female end more). 2. Get enough heat (430F) to the base end of the chain feral to get the silver solder to wick w/o too much damage to the Teflon sheath covering the cable. I think if I file down about 1/16" off the feral (provide a 1/16" gap between the top of the feral and end of sheath) and have the cable submerged and held in water up as far as possible, I can get this done. Oh, of course I will also re-crimp the union before silver soldering.

So why? Was this done by design to allow failure so other more expensive components don't fail, or to allow failure to sell very expensive SS chain/cables, or both?

Image

_________________
Thank you,
Roy Niswanger


Top
 Profile  
 
PostPosted: Mon Nov 02, 2020 5:26 pm 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 15027
Location: Oceanside, California
A failure of this kind is quite rare, I would think, and would have been a bad roller swage job.

This should be covered by warranty as it is clearly defective.

_________________
Matt Miller
Former - Director of Parts and Accessory Sales
Warranty and Technical Support
Hobie Cat USA
(Retired 11/7/2022)


Top
 Profile  
 
PostPosted: Tue Nov 03, 2020 2:03 pm 
Offline
Site Rank - Admiral

Joined: Fri Jul 13, 2018 9:01 am
Posts: 152
Location: Near Austin, TX
mmiller wrote:
A failure of this kind is quite rare, I would think, and would have been a bad roller swage job.

This should be covered by warranty as it is clearly defective.


Well Matt, a free replacement would be great, just need to follow a process right?

In the meantime, I repaired it on my own:


_________________
Thank you,
Roy Niswanger


Top
 Profile  
 
PostPosted: Tue Nov 03, 2020 2:37 pm 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 15027
Location: Oceanside, California
Have your dealer file a claim. Will be interested to see how that holds up!

_________________
Matt Miller
Former - Director of Parts and Accessory Sales
Warranty and Technical Support
Hobie Cat USA
(Retired 11/7/2022)


Top
 Profile  
 
PostPosted: Tue Nov 03, 2020 3:38 pm 
Offline
Site Rank - Admiral

Joined: Fri Jul 13, 2018 9:01 am
Posts: 152
Location: Near Austin, TX
mmiller wrote:
Have your dealer file a claim. Will be interested to see how that holds up!


Me too! After I crimped it, I put the chain end in my vice (padded with wood blocks) and yanked pretty damn hard. So with the new (albeit not as good as factory) crimp and the silver bearing solder job and installing now with correct load/tension, it will be interesting to see how long it holds up. I will let you all know.

_________________
Thank you,
Roy Niswanger


Top
 Profile  
 
PostPosted: Sun Nov 22, 2020 2:42 pm 
Offline
Site Rank - Admiral

Joined: Fri Jul 13, 2018 9:01 am
Posts: 152
Location: Near Austin, TX
Uggg, fix didn't last but about 20 mins of pedaling! Just filed a claim with ACK.

_________________
Thank you,
Roy Niswanger


Top
 Profile  
 
PostPosted: Mon Nov 23, 2020 10:05 pm 
Offline
Site Rank - Old Salt

Joined: Thu Dec 10, 2009 2:40 pm
Posts: 1365
Roy, after chuckling, I give you an "A" for effort!

_________________
Dr.SteelheadCatcher
Hood River, OR


Top
 Profile  
 
PostPosted: Tue Nov 24, 2020 9:32 am 
Offline
Site Rank - Admiral

Joined: Fri Jul 13, 2018 9:01 am
Posts: 152
Location: Near Austin, TX
Dr.SteelheadCatcher wrote:
Roy, after chuckling, I give you an "A" for effort!


Making others laugh is fine, making oneself laugh is mostly the goal, I do laugh at myself a fair amount :) I think I needed more heat to the twisted cable, not much if any silver solder flow.

_________________
Thank you,
Roy Niswanger


Top
 Profile  
 
PostPosted: Tue Nov 24, 2020 9:34 am 
Offline
Site Rank - Admiral

Joined: Fri Jul 13, 2018 9:01 am
Posts: 152
Location: Near Austin, TX
jackstaygnat wrote:
A failure of this kind is quite rare, I would think, and would have been a bad roller swage job.

This should be covered by warranty as it is clearly defective.


Interesting, as a first post too, to basically quote what Matt Miller said? Also interesting you registered a couple of months back and this is your first post. Thanks for stopping by to chime in.

_________________
Thank you,
Roy Niswanger


Top
 Profile  
 
PostPosted: Thu Jan 14, 2021 4:50 am 
Offline
Site Rank - Deck Hand

Joined: Thu Jan 14, 2021 3:12 am
Posts: 8
Location: Denmark, Europe
Hi niswanger,

I think you are right! Looking at the teflon coat on the cable, it doesn't look like you have had enough heat on the steel wire. It needs to be glowing red, and then the teflon will be burning in the end.

I have tried a similar exercise, using a grub screw instead of the thread (in opposite end of the chain). I drilled out the hex shape and soldered the wire down there. Afterwards I filed the screw, until it had the shape to go into the slot in the drum. It worked for a long time. :)


Top
 Profile  
 
PostPosted: Sun Jan 31, 2021 4:08 pm 
Offline
Site Rank - Captain

Joined: Thu Mar 29, 2007 4:43 am
Posts: 107
As to why they crimp and not solder, that's pretty simple. Design for manufacture. If a crimp holds, it fast and easy. perfect for keeping manufacturing costs down.

Same reason why rivets are often used instead of nuts and bolts. Speed.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group