Hobie Forums :: View topic - Mounting Hardware for original Bob Mast Float

The full sized Bob is pretty big for the 16, but there was a kit with all the hardware.

https://media.hobie.com/item_attachments/30113z52.pdf

8010121 RIVET POP 3/16x5/8 PH-SS 2
8010141 RIVET 3/16 x 3/4" PH-AL 1
8010181 RIVET POP 3/16x1/4 PH-SS (ABA) 4
8011291 RIVET CAP 15/64 SS 3
8080711 WASHER 5/8x1-5/16 SS 2
36600031 BEARING 5/8 X 1-3/8 X 7/16 2
36600040 COTTER RING 1-1/8 X .072 1
38120011 EYESTRAP-LRG SS 2
36600011 SHAFT (1)

We don't have all the parts. One is just a PVC pipe as a spacer.

The bearings are in stock as well as rivets and straps... and the shaft.

Or a better fit:

30115 MAST FLOAT KIT WV/H14/16 "BABY BOB"

Author:	dwotwell [ Tue Jun 09, 2020 8:38 am ]
Post subject:	Mounting Hardware for original Bob Mast Float
I was recently given an original Bob Mast Float - but not any of the mounting hardware. Can anyone tell me what replacement parts I need to order to mount this properly on my old Hobie 16? I have a pre-comp tip mast. Thanks!

Author:	mmiller [ Tue Jun 09, 2020 10:15 am ]
Post subject:	Re: Mounting Hardware for original Bob Mast Float
The full sized Bob is pretty big for the 16, but there was a kit with all the hardware. https://media.hobie.com/item_attachments/30113z52.pdf 8010121 RIVET POP 3/16x5/8 PH-SS 2 8010141 RIVET 3/16 x 3/4" PH-AL 1 8010181 RIVET POP 3/16x1/4 PH-SS (ABA) 4 8011291 RIVET CAP 15/64 SS 3 8080711 WASHER 5/8x1-5/16 SS 2 36600031 BEARING 5/8 X 1-3/8 X 7/16 2 36600040 COTTER RING 1-1/8 X .072 1 38120011 EYESTRAP-LRG SS 2 36600011 SHAFT (1) We don't have all the parts. One is just a PVC pipe as a spacer. The bearings are in stock as well as rivets and straps... and the shaft. Or a better fit: 30115 MAST FLOAT KIT WV/H14/16 "BABY BOB"

Author:	dwotwell [ Tue Jun 09, 2020 10:35 am ]
Post subject:	Re: Mounting Hardware for original Bob Mast Float
mmiller wrote: The full sized Bob is pretty big for the 16, but there was a kit with all the hardware. https://media.hobie.com/item_attachments/30113z52.pdf 8010121 RIVET POP 3/16x5/8 PH-SS 2 8010141 RIVET 3/16 x 3/4" PH-AL 1 8010181 RIVET POP 3/16x1/4 PH-SS (ABA) 4 8011291 RIVET CAP 15/64 SS 3 8080711 WASHER 5/8x1-5/16 SS 2 36600031 BEARING 5/8 X 1-3/8 X 7/16 2 36600040 COTTER RING 1-1/8 X .072 1 38120011 EYESTRAP-LRG SS 2 36600011 SHAFT (1) We don't have all the parts. One is just a PVC pipe as a spacer. The bearings are in stock as well as rivets and straps... and the shaft. Or a better fit: 30115 MAST FLOAT KIT WV/H14/16 "BABY BOB" Thanks Matt!

Hobie Forums http://www.hobie.com/au/en/forums/

Mounting Hardware for original Bob Mast Float http://www.hobie.com/au/en/forums/viewtopic.php?f=14&t=66679	Page 1 of 1

Page 1 of 1	All times are UTC - 8 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/