| Hobie Forums http://www.hobie.com/au/en/forums/ |
|
| A question about the Spi kit xpecially for MM http://www.hobie.com/au/en/forums/viewtopic.php?f=14&t=8820 |
Page 1 of 1 |
| Author: | italianhobie [ Sat Mar 01, 2008 1:19 pm ] |
| Post subject: | A question about the Spi kit xpecially for MM |
Hi there... I want just to know if it's safe to put the spi kit over a 02 european boat. There is some issue related to this? Someone can give some tips on how to use the spi? Thanx a lot Max |
|
| Author: | Flemse [ Tue Mar 04, 2008 2:55 am ] |
| Post subject: | Re: A question about the Spi kit xpecially for MM |
italianhobie wrote: Hi there...
I want just to know if it's safe to put the spi kit over a 02 european boat. There is some issue related to this? Someone can give some tips on how to use the spi? Thanx a lot Max Hi Max you (and your crew) will love it ! please mail me is you have any Qs or better yet- go to lake Garda for easter HC16 SPI camp at malcesine! i have been sailing with SPi for a year so i know a little.. Flemse (Hobie coach ) [email protected] |
|
| Author: | mmiller [ Tue Mar 04, 2008 11:42 am ] |
| Post subject: | Spin kit on a euro H16? |
Spin kit on a euro H16? No problem at all. THe Euro 16 has an all metal mast, so is better suited for it than the US CompTip mast. There are lots of books on spinnaker handling. |
|
| Author: | Siam [ Wed Mar 05, 2008 3:14 am ] |
| Post subject: | |
I was told by UK dealer older boats pre 2003 needed the bows re inforced does anyone know anything about this? |
|
| Author: | italianhobie [ Wed Mar 05, 2008 7:59 am ] |
| Post subject: | |
Siam wrote: I was told by UK dealer older boats pre 2003 needed the bows re inforced does anyone know anything about this?
This is my fear, i think to reinforce the bow under with epoxy and fiberglass. Any tips? |
|
| Author: | Flemse [ Wed Mar 05, 2008 9:11 am ] |
| Post subject: | |
Siam wrote: I was told by UK dealer older boats pre 2003 needed the bows re inforced does anyone know anything about this? I never heard of that ...mine is a 1998 HC16 and it is holding up fine. with the SPI kit on.
|
|
| Author: | mmiller [ Wed Mar 05, 2008 10:30 am ] |
| Post subject: | |
Maybe they are talking about the bow tang areas, but the boats have been pretty much the same construction in the USA since the early days. No changes that would effect spinnaker use. You never know about Hobie Europe though. They have done their own thing over the years... making changes etc. Maybe they just want to promote new boat sales though? |
|
| Author: | Claus [ Tue Mar 25, 2008 1:35 pm ] |
| Post subject: | |
I have reinforced the bows of my 91 H16 for using the spi kit, after seeing a few broken bows on the last europeans. Just get off the gelcoat in the lower U-shaped part of the bows (say 5 cm to each side, its just the very tips that brake), give it a few layers of fiber and terminate with gelcoat (you just fill the "U"). Then open the hole for the screws and you are done. I think Hobie Europe also sells some plastic parts to reinforce the bows, but the fiber works perfectly and you will not notice it from above. |
|
| Page 1 of 1 | All times are UTC - 8 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|