Hobie Forums
http://www.hobie.com/au/en/forums/

YakAttackTracks: Which For AI2 ?
http://www.hobie.com/au/en/forums/viewtopic.php?f=71&t=57154		 Page 1 of 1
Author:  PeteCress [ Sun Mar 20, 2016 6:07 pm ]
Post subject:  YakAttackTracks: Which For AI2 ?
I'm not sure exactly what I am going to do furling-line/sheet-line-wise, but it's pretty sure to involve mounting things on the gunwale(s).

My gut says "Just cover all of both gunwales with YakAttack track and then start playing around."

The YakAttack system seems to allow easy relocation fore-and-aft in light of hands-on experience - cam cleats, for instance...

At http://www.yakattack.us/by-application/ ... -hardware/ I see that there are two types of track:

  • GT90 with a single row of screws down the center
    .
  • GT175 with a row of screws on each side of the track.

Is one or the other the right fit for all of the AI's gunwale area? (bearing in mind that the width of the gunwales varies a lot)

Also, I see "FullBack Backing Plate". May I assume that adding backing plates is a no-brainer?

Finally, I see that now they are offering a price point option with GTSL175 and GTSL90 tracks made out of "Polymer" (whatever *that* is...) instead of alu. Safe to say those would be a no-no for sheet cleat mounting?

In the interest of full disclosure.... I just fired off an email to YakAttack support - basically with the contents of this post.

But I still want to pose the question here because of the obvious (?) AI2-specific accessibility issues of various points along the AI2's gunwales - i.e. mainly is installation of these tracks even possible along some areas?
Author:  johnnybravo [ Mon Mar 21, 2016 2:13 pm ]
Post subject:  YakAttackTracks: Which For AI2 ?
On my AI-2015 I installed these models:
GT90-08GT90 GearTrac, 8"
GT90-04GT90 GearTrac, 4"

in combination with
FB-GT90-04GT90 / GTSL90 backing plate, 4"
FB-GT90-08GT90 / GTSL90 backing plate, 8"

When they are mounted in this way they are extremely durable.

Image
Image
Image

Image

In my opinion, the model GT175 (GT175-04 - GT175 GearTrac, 4") can fit in only one place of the kayak.
Image

But I'm not sure if FBH-GT175 (FullBack backing plate) will fit inside.
Image


Sent from my iPhone using Tapatalk
Author:  NOHUHU [ Mon Mar 21, 2016 5:36 pm ]
Post subject:  Re: YakAttackTracks: Which For AI2 ?
Very helpful info guys. Thanks.
Author:  unagimon [ Tue Mar 22, 2016 9:55 am ]
Post subject:  Re: YakAttackTracks: Which For AI2 ?
looks great! Could you help me find the mounting hardware that you used to connect your starport mounts to the track?

Thank you!
Author:  johnnybravo [ Tue Mar 22, 2016 12:04 pm ]
Post subject:  Re: YakAttackTracks: Which For AI2 ?
MB15-12-6 MightyBolt, 1-1/2" lg - 1/2 wide, 6 pack
Image

KB1420-6 Threaded Knobs, 1/4-20 Threads, 6 pack
Image
Author:  PeteCress [ Tue Mar 22, 2016 1:09 pm ]
Post subject:  Re: YakAttackTracks: Which For AI2 ?
NOHUHU wrote:
...helpful...
Here's something I thought was worth the fifteen bucks I paid for it: http://www.yakattack.us/RB0832_p/rb0832.htm

Basically a couple of hollowed-out tapered screws that allow positioning/installation of back plates without inside access by the hands to the area of installation.

Vid at: https://www.youtube.com/watch?v=6EnHBEEQHYs
Author:  NOHUHU [ Tue Mar 22, 2016 3:53 pm ]
Post subject:  Re: YakAttackTracks: Which For AI2 ?
Well Lookey-here! Aren't these cute...
Image

http://www.yakattack.us/GearTrac_Bar_Clamp_1_1_8_Diameter_p/bc-gt175-1625.htm
Author:  johnnybravo [ Wed Mar 23, 2016 4:42 am ]
Post subject:  Re: YakAttackTracks: Which For AI2 ?
I put them on my old Pro Angler 12 and they did a perfect job.
http://youtu.be/LO0O7LN_rDY


Sent from my iPhone using Tapatalk
Page 1 of 1 All times are UTC - 8 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/