Hobie Forums
http://www.hobie.com/au/en/forums/

Side Scan transducer mounting options for HB or Lowrance???
http://www.hobie.com/au/en/forums/viewtopic.php?f=78&t=50410		 Page 1 of 1
Author:  usmcman001 [ Wed Feb 19, 2014 12:27 pm ]
Post subject:  Side Scan transducer mounting options for HB or Lowrance???
Hey everyone I am looking for pics and opinions on the best way to mount a side scan transducer on a PA12. I am really leaning toward the HDS 7 bundle and looking for opinions on mounting the larger transducer. I know I can mount the transducer on a side arm but looking for other way of doing so to have a cleaner look.

I was thinking about possibly mounting on the rear grab handle centerline with boat. Any opinions on this as far a disturbance from rudder or cavitation? I would modify a RAM mount and use this for mounting so I can swing up and away when needed. Thanks everyone!
Author:  Kalgrm [ Wed Feb 19, 2014 5:33 pm ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
I can't help you with the Lowrance fittings, but I've mounted my HB sidescan transducer where the Lowrance Ready mounts is, underneath the hull. It's permanently mounted there.

Here are some pics of the mount I made to give you some ideas. The material is 3mm aluminium plate and 2mm x 40x40mm aluminium angle. The protective blob of material in front of the transducer is epoxy resin putty.

Image
This one shows the setup from above.

Image
A side view of the bracket

Image
Now fitted to the hull in place of the plastic hull mount supplied by Hobie.

Image
The view from the rear of the hull with the yak resting on flat ground.

Cheers,
Graeme
Author:  SteveK [ Fri Feb 21, 2014 7:12 pm ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
There's no need to make the plate, do the same thing your doing but to the plastic cover. Slightly recess the transducer into the cover from the outside, basically insert the cable and mounting area by cutting the cover than build it up with marine goop both from the outside and inside. Make sure that the transducer beam clears the hull on both sides. The transducer can take a beating so don't worry about damaging it. There is a photo in this forum of what your looking for.

tight lines
Steve
Author:  Kalgrm [ Sat Feb 22, 2014 1:31 am ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
I'm sure the transducer can take a beating. It's the original plate (after being cut) that I thought would cop a hiding.

I also wanted a protective blob in front of the transducer to prevent it being knocked up and out of alignment and to prevent weed catching it. Epoxy won't stick to PE, but there may have been something else I could have used.

Cheers,
Graeme
Author:  SteveK [ Sat Feb 22, 2014 9:07 am ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
http://bassyaks.com/wp-content/uploads/2014/02/20140222_132708-800x600.jpg
Use marine goop
layer it on and it will never move
Author:  svendawg [ Sat Feb 22, 2014 9:31 pm ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
SteveK wrote:
http://bassyaks.com/wp-content/uploads/2014/02/20140222_132708-800x600.jpg
Use marine goop
layer it on and it will never move


This looks sweet. Do you have any pictures of the plastic plate before you gooped the transducer
Author:  Gotta Get Me Sum [ Sun Feb 23, 2014 3:47 am ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
look at kdfu.com.au rigged section of posts, revo 13 with retractible transducer for humm 598 sidescan,

has photo.s and parts cost less than $15 , no extra holes or mods to kayak, other than cutting base plate,

would attach photo,s but unsure how to on this forum.
cheers
Author:  Kalgrm [ Sun Feb 23, 2014 3:50 am ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
SteveK wrote:
http://bassyaks.com/wp-content/uploads/2014/02/20140222_132708-800x600.jpg
Use marine goop
layer it on and it will never move


That does indeed look very good.

(Marine goop is not available here in Australia, as far as I know. Lots of good things you have aren't available here … :( )

Cheers,
Graeme
Author:  Gotta Get Me Sum [ Sun Feb 23, 2014 2:43 pm ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
Kalgrm wrote:
SteveK wrote:
http://bassyaks.com/wp-content/uploads/2014/02/20140222_132708-800x600.jpg
Use marine goop
layer it on and it will never move


That does indeed look very good.

(Marine goop is not available here in Australia, as far as I know. Lots of good things you have aren't available here … :( )

Cheers,
Graeme


have a look at this, retractible humm side scan transducer 598
http://www.kfdu.com.au/forum/viewtopic.php?f=12&t=37230
cheers
Author:  Kalgrm [ Mon Feb 24, 2014 4:34 pm ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
Gotta Get Me Sum wrote:
have a look at this, retractible humm side scan transducer 598
http://www.kfdu.com.au/forum/viewtopic.php?f=12&t=37230
cheers

Nice, but it won't work on a PA14 because the hull design does not have a place to lift the transducer pole through. The scupper from the transducer well for the cable is placed behind and beneath the Vantage seat and is not open at the top of the hull. (The cable comes through a hole on a vertical part of the hull.)

Cheers,
Graeme
Author:  fishingfiend [ Wed Mar 12, 2014 11:45 am ]
Post subject:  Re: Side Scan transducer mounting options for HB or Lowrance
I really like the setup, but it requires a machine shop. This is where most of us will fail. A year ago, I just cut out the bottom of the lowrance mount and have had no issues since. Just providing an alternative...

viewtopic.php?f=78&t=46839

Image
Page 1 of 1 All times are UTC - 8 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/