Return to Hobie.com
Hobie Forums
It is currently Thu Mar 28, 2024 4:27 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Sat Jan 15, 2011 10:37 am 
Offline
Site Rank - Old Salt

Joined: Sun Mar 16, 2008 10:46 pm
Posts: 470
So tight that one will work only in one trunk, and won't work/slide in the other at all. Just jams about 3" down. The trunks only have the factory installed fabric guides pieces at the ends.

Is there a recommended clearance?

Should the boards be sanded until there is clearance and a hold down kit be attached, as on the Tiger?

Should they just be waxed to improve slickness and left alone?

Should I post this on the Tiger forum?

Will my investments make over 8% for this new year...


Top
 Profile  
 
PostPosted: Sat Jan 15, 2011 1:14 pm 
Offline
Site Rank - Old Salt

Joined: Mon May 09, 2005 10:25 am
Posts: 4176
Location: Jersey Shore
Is it a brand new boat? On the 20, there was a bit of a break-in period for the carpet pads when the boat was new, the boards were very tight. Have you gotten the boards wet before inserting? Have you tried silicone or McLube on the daggerboards and carpet? No way I would sand the boards. Maybe remove some of the carpet if it came to that. I would start with lubrication.

sm


Top
 Profile  
 
PostPosted: Sun Jan 16, 2011 6:55 pm 
Offline
Site Rank - Old Salt

Joined: Sun Mar 16, 2008 10:46 pm
Posts: 470
Not brand new. Don't get me wrong, both work when in the correct place. Just not as smoothly as I'd like. Was watching a video (not FX) and noticed the daggerboard being slid easily up on change of tack with a flick of the wrist.

The non-uniformity in thickness is odd for factory boards. Lubing them up I thought not so great, but I haven't had time to experiment. Afraid I might lube my feets. Putting a whole new meaning in flying a hull. Or flying off a hull.

I'll order the daggerboard lube. What's part #? :)


Top
 Profile  
 
PostPosted: Sun Jan 16, 2011 8:58 pm 
Offline
Site Rank - Old Salt

Joined: Sat Feb 24, 2007 8:45 pm
Posts: 1668
Location: Northfield Minnesota
Wax your boards, and use pledge as lube.


Top
 Profile  
 
PostPosted: Mon Jan 17, 2011 4:39 am 
Offline
Site Rank - Old Salt

Joined: Mon May 09, 2005 10:25 am
Posts: 4176
Location: Jersey Shore
There's no part number for "daggerboard lube." Just get a can of silicone spray from an auto parts store or order a can of McLube. Prop the boards up and spray down both sides (or maybe just do one side and test - if you put on too much silicone, the boards may not stay up).
Your feet are not going to slip unless you spray the hull.

sm


Top
 Profile  
 
PostPosted: Mon Jan 17, 2011 4:46 pm 
Offline
Site Rank - Old Salt

Joined: Sun Mar 16, 2008 10:46 pm
Posts: 470
Thanks.

:) <------------------- smiley on the daggerboard lube, srm.

Do they make a halyard conditioner and what is the part number for that? :wink:


Top
 Profile  
 
PostPosted: Mon Jan 24, 2011 6:42 am 
Offline
Site Rank - Captain

Joined: Tue Sep 20, 2005 9:29 am
Posts: 50
Location: Low Country - SC
Jimbo,

Check the guides to ensure they are clean (and all of them are properly in place). It may also be time to replace them with some new material.

Spray them with McLube once you are certain that there is not any sand or gunk in them. I found that lubricating the guides was more effective than the boards (fabric holds the McLube) since the boards lose the coating much faster with water passing over them. I also used to spray the cradles with McLube, same thing here with the material holding the McLube a lot longer than the boat hulls. Wax is great on the hulls for the first couple times and then quickly it is gone off the bottom and you are putting much more effort into it once again.

Mike


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group