Return to Hobie.com
Hobie Forums
It is currently Fri Mar 29, 2024 3:04 am

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: Replacing main traveler
PostPosted: Sun Oct 03, 2004 8:35 pm 
Offline
Site Rank - Captain

Joined: Mon Aug 30, 2004 12:31 pm
Posts: 88
Location: Redlands, Ca
I recently purchased an older hobie (74) to replace my worn (79) its in better condition and looks a lot sharper.

Ive noticed alot of upgrades from my old boat that arent on the 74 such as...

The main traveler, its plastic, not on rollers and sized for the old main sheet system. I have a nicer traveler in my 79 that I want to swap out, how do i do this? Do I have to take the rivets out of the track? Ive heard alot of greif about doing that.. is there an easier way?

Thanks


Top
 Profile  
 
 Post subject:
PostPosted: Mon Oct 04, 2004 3:45 pm 
Offline
Site Rank - Admiral

Joined: Tue Mar 30, 2004 9:32 pm
Posts: 198
Location: West Texas
I replaced my traveler just a few weeks ago. You have to drill 3 rivets from one side of the track to bend it up enough to slide the traveler in or out.

I ordered new counter-sunk rivets from Murray's, and got a bunch of little washers to slide over the "nail" portion since my rivet gun wouldn't go into the track. (The washers bring the "head" of the rivet up out of the track.)

Anyway, it was pretty easy.

_________________
Warm regards,

Jim

Image

"A little crazy but with big balls."


Top
 Profile  
 
 Post subject:
PostPosted: Mon Oct 04, 2004 6:29 pm 
Offline
Site Rank - Captain

Joined: Mon Aug 30, 2004 12:31 pm
Posts: 88
Location: Redlands, Ca
Thanks, Im gonna try it this weekend!


Top
 Profile  
 
 Post subject:
PostPosted: Tue Oct 05, 2004 6:11 pm 
Offline
Authorized Hobie Dealer

Joined: Mon Jun 02, 2003 7:35 pm
Posts: 1369
Location: 315 N. Hwy 79 Panama City Beach, FL 32413 850-235-2281
Be careful using the rivets from Murrays. We used some on out last job and they did not work very well, they did not seat as flush as they should have and ended up tearing the traveler car up again, make sure they are counter sunk and they counter sink. We have never had a problem with the ones from Hobie. Just my 2 cents worth


Thanks,
Brad Stephens
www.sunjammers.com
Authorized Hobie/Vanguard Dealer
Hobie Division 15 Chairman
[email protected]
850-235-2281
Panama City Beach, FL


Top
 Profile  
 
 Post subject:
PostPosted: Tue Oct 05, 2004 7:00 pm 
Offline
Site Rank - Admiral

Joined: Tue Mar 30, 2004 9:32 pm
Posts: 198
Location: West Texas
Interesting point. Mine didn't "counter sink" quite as much as I would have liked, but I figured it should be okay because it's fairly close to the edge. You think I should replace them?

_________________
Warm regards,

Jim

Image

"A little crazy but with big balls."


Top
 Profile  
 
 Post subject:
PostPosted: Wed Oct 06, 2004 5:24 am 
Offline
Hobie Approved Guru

Joined: Mon Jul 14, 2003 7:11 pm
Posts: 5197
Location: Detroit, MI
The trick on replacing traveller track rivets is two-fold:

1) Make sure the track is held down tightly to the crossbar. This can be a simple as tightly wrapping a piece of line around the crossbar / track assembly. The rivets will not pull the track down.

2) The nose of the rivet gun has to seat firmly on the top of the rivet, which in turn, has to be firmly seated in the countersink. Most rivet guns will not fit into the track, so you can either stack washers on the tail of the rivet (OK) or modify the nose of the rivet gun to fit in the track (best).

A preventative measure is to deepen the countersink in the track a little (emphasis on "a little") before setting the rivets. That will ensure the rivet heads are below the bottom of the track.

After the fact, you can grind down the protruding rivet heads with a Dremel tool. Just be careful. Aluminum (track) is way softer than stainless steel (rivets).

Jim, you're right that you don't have to worry too much about the rivets on the end. Until you jibe in heavy air and the traveller hangs up on a rivet head - on the wrong side of the boat! :twisted:

(that's happened to me on my 17 and the result was an unexpected swim)


Top
 Profile  
 
 Post subject: Rivets at end of track
PostPosted: Wed Oct 06, 2004 9:21 pm 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 15027
Location: Oceanside, California
Reality is that the car should be prevented from reaching the end of the track to prevent damage from hitting the casting. That is normally done by tieing a knot in the traveler line as a limiter. The car position rarely would be more than about 3/4 out for best performance anyway, so maybe it is not a real problem and not worth drilling and replacing.

_________________
Matt Miller
Former - Director of Parts and Accessory Sales
Warranty and Technical Support
Hobie Cat USA
(Retired 11/7/2022)


Top
 Profile  
 
 Post subject:
PostPosted: Thu Oct 07, 2004 4:24 am 
Offline
Site Rank - Admiral

Joined: Tue Mar 30, 2004 9:32 pm
Posts: 198
Location: West Texas
Good to know, Matt. Thanks!

_________________
Warm regards,

Jim

Image

"A little crazy but with big balls."


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jan 14, 2005 8:02 pm 
Offline
Site Rank - Captain

Joined: Mon Aug 30, 2004 12:31 pm
Posts: 88
Location: Redlands, Ca
I finally got around to replacing the main traveler from the old plastic to the newer bering and metal. It went easier than expected, I had some problems with the rivet tool but I ebayed a good one for 60 bucks and it worked with no problems! The rivets didnt counter sink like i wanted them too but I took a metal spacer and hammered them down some more and the are near flush, the traveler doesnt hang up at all...

Thanks for all your input!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group