Return to Hobie.com

Hobie Forums

It is currently Tue Jan 16, 2018 11:41 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Mon Apr 25, 2016 5:59 pm 
Offline
Site Rank - Captain

Joined: Mon Apr 18, 2016 1:12 pm
Posts: 42
Location: Sapulpa, Oklahoma
Several others have posted theirs, but here is a slightly different twist using similar methods to give other ideas.

First I used larger furling line so I could grip it easier without it cutting into my hand. The advantage is that it also spools out farther on the drum giving more leverage, but the downside is when storing the sail it barely all fits.
Image

Second I added a 29mm cheek block in the outer edge of the crossbar. I did have to drill and tap the bar since the existing holes do not line up. Moving the block out like this helps keep the furling line out of the way of your feet.
Image

Third I added a mounting rail just above the pocked by the front seat and added the controls here. This is super handy for the front seat position as the cleats are right there by your hand. Maybe a little to the side as you pull on them, but i'm usually in the rear seat anyway.
Image
Image

How does this help the rear seat? Notice the line guide also mounted to the rail? This is positioned so that the line is easily cleated and uncleated from the rear seat by aligning it through the cleat. Without this, it would be nearly impossible to lower the line enough to grab the cleat, instead it would always be lifted to the top of the cleat due to the angle.
Image

The rear unfurling line is still stock, but I do plan to move the cleat closer to the rear seat, but for now this works a LOT better.


Top
 Profile  
 
PostPosted: Wed Apr 27, 2016 2:14 am 
Offline
Site Rank - Old Salt

Joined: Tue Jun 19, 2007 6:14 pm
Posts: 3085
Location: South Florida
Nice!

Keith

_________________
2015 AI 2, 2014 Tandem

"Any intelligent fool can make things bigger and more complex ... It takes a touch of genius and a lot of courage to move in the opposite direction." A. Einstein


Top
 Profile  
 
PostPosted: Sat Dec 17, 2016 2:21 pm 
Offline
Site Rank - Captain

Joined: Sat Dec 17, 2016 2:00 pm
Posts: 28
Looks like a very practical setup. Quick question on another topic - looks like you are using the Harbor Freight trailer - how did you extend the front to accommodate the length of the TI?
Thanks.


Top
 Profile  
 
PostPosted: Sun Jan 01, 2017 11:19 am 
Offline
Site Rank - Captain

Joined: Fri Apr 18, 2014 7:29 am
Posts: 26
Nice setup.

Could you provide the specific part numbers for the cheek block, rail (length?) and dual cam cleat that you used? Was your line guide a DIY job?

Also, does the rail have a backing plate inside the hull or washers & nuts? And how difficult is access to the inner hull where the rail is mounted?

Thanks,

Gary

2014 Tandem Island
1984 Hobie Hawk RC Glider


Top
 Profile  
 
PostPosted: Mon Jan 02, 2017 6:02 pm 
Offline
Site Rank - Captain

Joined: Fri May 13, 2016 8:06 pm
Posts: 37
Location: Laem Sing, Chanthaburi, Thailand
Nice setup. I am also interested in your answers to Gary's questions.

I'm assuming you've replaced the furling line with 6mm line. Could you please tell me the length of that 6mm line you were able to fit on the spool to reach back to the rear seat position?

Thanks
John


Top
 Profile  
 
PostPosted: Tue Mar 21, 2017 2:38 pm 
Offline
Site Rank - Captain

Joined: Sat Dec 17, 2016 2:00 pm
Posts: 28
Kleake, that is a great setup. I have contacted all the aftermarket people and Harken themselves and shown them your pictures but no one knows where your twin cam cleat mount/plate comes from! Can you tell us where you got it?
Thanks.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group