Return to Hobie.com
Hobie Forums
It is currently Fri Mar 29, 2024 7:41 am

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: quality control
PostPosted: Wed Aug 16, 2017 12:08 am 
Offline
Site Rank - Deck Hand

Joined: Tue Aug 15, 2017 11:58 pm
Posts: 6
I recently purchased a revolution 13, and have noticed that one of the two bottom holes under hull (hole closest to mirage drive) has brass bolt exposed with jagged plastic around same. Is this normal or just a cosmetic issue? I figured for $2500 this would not be overlooked. I have a rev 11 on order and am reconsidering my purchase. The hole forward which connects to mast is flush with the hull.


Top
 Profile  
 
 Post subject: Re: quality control
PostPosted: Wed Aug 16, 2017 7:51 am 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 15027
Location: Oceanside, California
One is for the fitting below the mast base. The second reinforces the forward ledge of the drive well. Both typically would have small caps (panel rivets) covering the threads. This is a molded-in fitting and some flashing (plastic bits) around them is normal. They can sometimes protrude a bit. This is normal for a roto-molded boat.

The threads are how the part is held into the mold. The threads do not extend through the brass and the brass parts are completely encased in plastic inside the boat.

_________________
Matt Miller
Former - Director of Parts and Accessory Sales
Warranty and Technical Support
Hobie Cat USA
(Retired 11/7/2022)


Top
 Profile  
 
 Post subject: Re: quality control
PostPosted: Wed Aug 16, 2017 12:48 pm 
Offline
Site Rank - Deck Hand

Joined: Tue Aug 15, 2017 11:58 pm
Posts: 6
thanks for reply, the brass bolt head itself is visible and protruding outside hull. it appears extra plastic was added as well. assuming this is not normal as other hole is flush and encased within hull.


Top
 Profile  
 
 Post subject: Re: quality control
PostPosted: Wed Aug 16, 2017 1:06 pm 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 15027
Location: Oceanside, California
Yes, they can sometimes protrude a bit as a bump on the bottom.

How about a photo?

_________________
Matt Miller
Former - Director of Parts and Accessory Sales
Warranty and Technical Support
Hobie Cat USA
(Retired 11/7/2022)


Top
 Profile  
 
 Post subject: Re: quality control
PostPosted: Wed Aug 16, 2017 5:19 pm 
Offline
Site Rank - Deck Hand

Joined: Tue Aug 15, 2017 11:58 pm
Posts: 6
For whatever reason I cannot attach photos to this forum. I will send you email from [email protected] with photos in reference. Thanks.


Top
 Profile  
 
 Post subject: Re: quality control
PostPosted: Thu Aug 17, 2017 8:54 am 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 15027
Location: Oceanside, California
For future reference:

mmiller wrote:
Posting an image... Images must be hosted at a location on the internet. (Suggested site: imgur.com or flickr.com)

Check the image below. Right click on the image to see the copy image address popup option:

Image

Image URL ends in .jpg or .png or similar.

Navigate to your image page. Right click the image and copy the "propeties". This must be an image address (url) rather than a url to a page. Click the above image to test and look at properties and address (url).

Rather than a link to the page it was on. The address should end in something like .jpg or .gif

Use the buttons above the post text area to find the proper code.

Use [img]then%20the%20image%20url%20and%20click[/img] again.

Be sure to have the option " Disable BBCode " unclicked!

and you are done.

_________________
Matt Miller
Former - Director of Parts and Accessory Sales
Warranty and Technical Support
Hobie Cat USA
(Retired 11/7/2022)


Top
 Profile  
 
 Post subject: Re: quality control
PostPosted: Thu Aug 17, 2017 8:57 am 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 15027
Location: Oceanside, California
For others reference:

That appears about normal. Bit of excess flashing that could be trimmed, but the white "panel rivet" normally protrudes like that. The brass looks flush as it should be. They are all a little different. They are bolted in the mold and have to be released at a specific time period as it cools and starts shrinking. The hulls actually shrink 4% from the size of the mold, so there is some movement happening inside the mold before it cools enough to pull the hull out of the mold.

Image

_________________
Matt Miller
Former - Director of Parts and Accessory Sales
Warranty and Technical Support
Hobie Cat USA
(Retired 11/7/2022)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group