Return to Hobie.com
Hobie Forums
It is currently Thu Jun 26, 2025 5:44 am

Board index » Hobie Kayaking / Fishing » Open Forum - Kayaking

All times are UTC - 8 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
Dan Morera
 Post subject: Dremel Cutting
PostPosted: Mon Sep 05, 2016 12:05 pm 
Offline
Site Rank - Admiral

Joined: Tue Jul 12, 2011 6:21 am
Posts: 157
Hey guys,

While I wait for my new outback to arrive I spend my days thinking of all of the nasty stuff I am going to do to my kayak when it arrives. :o

I want to install the rectangular hatch as a lot of people do, but I was thinking about doing the cutting with my dremel as I think I have more control over the cuts. Anyone have done it this way? would it be possible ? Or is this going to give me a rougher cut than doing it with a jig saw?

Also plan on installing the PA H rails on it, can someone advice what size bolts and nuts to use for a strong mount?

Thanks in advance for your help.
Dan
Top
 Profile  
 
Irons
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 5:15 am 
Offline
Site Rank - Deck Hand

Joined: Wed Feb 17, 2016 1:53 pm
Posts: 12
DON'T.... I used my dremel and it did not do good. The dremel can run away quickly. If I had it to do over I would have used my jig saw.
Top
 Profile  
 
Thinwater skinner
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 7:43 am 
Offline
Site Rank - Old Salt

Joined: Mon Jun 01, 2009 11:59 am
Posts: 606
Dan Morera wrote:
I was thinking about doing the cutting with my dremel as I think I have more control over the cuts.
I use the dremel barrell sander drum to clean up the edges. I have not use the cutting tool for the main cuts.
Or is this going to give me a rougher cut than doing it with a jig saw?
Barrell sander for the rough cuts and clean up the edges... NOTE: cut smaller than athe hole you want and then sand to the correct size. YOu will be amazed how tight you can get the item to fit into the hole you cut.


Thanks in advance for your help.
Dan


Good luck and happy sailing? Yaking
Top
 Profile  
 
Dan Morera
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 7:50 am 
Offline
Site Rank - Admiral

Joined: Tue Jul 12, 2011 6:21 am
Posts: 157
Thank you guys
Top
 Profile  
 
HStrech
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 11:17 am 
Offline
Site Rank - Old Salt

Joined: Wed May 11, 2016 8:20 am
Posts: 439
If you're wanting to put an H-Rail on your Outback, I would recommend either the 9" (84626001) or 21" (part # 84626101) straight H-Rail bolt on kit with hardware included...the H-Rail upgrade kit is meant specifically for upgrading the PA12 or PA14, not for the Outback.

_________________
Howie Strech
Parts & Accessories Product Manager
Hobie Cat USA
Top
 Profile  
 
Dan Morera
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 11:31 am 
Offline
Site Rank - Admiral

Joined: Tue Jul 12, 2011 6:21 am
Posts: 157
HStrech wrote:
If you're wanting to put an H-Rail on your Outback, I would recommend either the 9" (84626001) or 21" (part # 84626101) straight H-Rail bolt on kit with hardware included...the H-Rail upgrade kit is meant specifically for upgrading the PA12 or PA14, not for the Outback.


I was planning on cutting it to size to have 2 long rails on each side. I have seen some pictures of a couple of outbacks like this, appears to work OK.
Top
 Profile  
 
HStrech
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 12:15 pm 
Offline
Site Rank - Old Salt

Joined: Wed May 11, 2016 8:20 am
Posts: 439
If you're okay with cutting and doing the mod yourself, I'm sure it'll work for ya.

_________________
Howie Strech
Parts & Accessories Product Manager
Hobie Cat USA
Top
 Profile  
 
Dan Morera
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 12:20 pm 
Offline
Site Rank - Admiral

Joined: Tue Jul 12, 2011 6:21 am
Posts: 157
HStrech wrote:
If you're okay with cutting and doing the mod yourself, I'm sure it'll work for ya.


Any advice regarding the nuts and bolts to use? Not sure how big the bottom holes are on those rail kits.

Thanks again for your help. 8)
Top
 Profile  
 
HStrech
 Post subject: Re: Dremel Cutting
PostPosted: Tue Sep 06, 2016 12:28 pm 
Offline
Site Rank - Old Salt

Joined: Wed May 11, 2016 8:20 am
Posts: 439
Dan Morera wrote:
HStrech wrote:
If you're okay with cutting and doing the mod yourself, I'm sure it'll work for ya.


Any advice regarding the nuts and bolts to use? Not sure how big the bottom holes are on those rail kits.

Thanks again for your help. 8)



The upgrade kit comes with all the mounting hardware needed to get the job done.

_________________
Howie Strech
Parts & Accessories Product Manager
Hobie Cat USA
Top
 Profile  
 
Dan Morera
 Post subject: Re: Dremel Cutting
PostPosted: Wed Sep 07, 2016 11:29 am 
Offline
Site Rank - Admiral

Joined: Tue Jul 12, 2011 6:21 am
Posts: 157
Thanks again.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Board index » Hobie Kayaking / Fishing » Open Forum - Kayaking

All times are UTC - 8 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group