Return to Hobie.com
Hobie Forums
It is currently Tue Jun 24, 2025 9:17 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: Baby Bob
PostPosted: Mon Aug 13, 2007 10:47 am 
Offline
Site Rank - Captain

Joined: Sun Jun 24, 2007 5:44 pm
Posts: 28
I have a very old style of mast (it is circular on top in order to make space for the halyard pulley) and when I tried to install a baby bob, I realized that I would be drilling through the halyard pulley if I drilled through the top of the mast. Putting the fasteners in would then result in me not being able to raise the sail. I still want to attach the bob, but I don't know how. The bob has the four small holes intended for attachment purposes. I was thinking about drilling through the mast lower down to avoid the halyard, then tying the bob on. Is this feasible? The halyard pulley has a hole through the axle that could also serve attachement purposes.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 11:00 am 
Offline
Authorized Hobie Dealer

Joined: Mon Jun 02, 2003 7:35 pm
Posts: 1369
Location: 315 N. Hwy 79 Panama City Beach, FL 32413 850-235-2281
there should be mounting instructions in the package for a non comptip installation. there are 4 short I'd guess 1/4" screws, you drill and tap the masthead for them to insert, they do not go in deep enough to effect the pulley.

_________________
Brad Stephens
[email protected]
(866) 786-5266 <--- Advice HOTline
http://www.sunjammers.com
www.facebook.com/sunjammers
Image


Top
 Profile  
 
 Post subject: Re: Baby Bob
PostPosted: Sun Aug 30, 2009 10:29 pm 
Offline
Site Rank - Captain

Joined: Wed Aug 26, 2009 4:24 pm
Posts: 73
I just had that problem too. You lightly drill but be very careful not to drill through the pulley, just the metal, then tap it. Wasn't as hard as it looks.


Top
 Profile  
 
 Post subject: Re: Baby Bob
PostPosted: Mon Aug 31, 2009 11:37 am 
Offline
Site Rank - Deck Hand

Joined: Mon Aug 31, 2009 11:32 am
Posts: 15
I just installed one on a 14 - no problme! Drill and tap 4x holes in the top cast piece. I used a #21 drill bit and I think 6x32 threads, as per the Baby Bob written instructions. Use 4x short SS machine screws (such that they are not long enough to contact the pulley for the main halyard), about 1/4" is good. You should be all set! Now I am adding the jib tracks and blocks to make her a 14T :) -glen


Top
 Profile  
 
 Post subject: Re: Baby Bob
PostPosted: Mon Aug 31, 2009 12:39 pm 
Offline
Site Rank - Admiral

Joined: Thu Dec 20, 2007 1:33 pm
Posts: 226
Location: Southern California
I just attached my Babybob last weekend.

You drill four holes in the mast head, but be very careful not to drill through the sheave (Pulley)

Next you tap the holes (10-32). I used two taps, a starting tap and then a bottoming tap as not to damage the sheave. You can get these at Sears.

The short scews are used to then mount the float.

_________________
1980 18 foot class A Unicorn catamaran
1977 Super Sunfish (sold)
1979 Hobie (sold)
1983 Hobie 16 Hawiian Sunset (sold)
1981 Hobie 16 Tequilla Sunrise (sold)
2008 Hobie 16 (sold)
2023 Hobie 16
Founding member of the "San Dimas Yacht Club"
John


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group